SparkFun: PRT-00341

Description: These are very slim, extremely light weight batteries based on the new Polymer Lithium Ion chemistry. This is the highest energy density currently in production. Each cells outputs a nominal 3.7V at 850mAh! Comes terminated with a standard 2-pin JST-PH connector – 2mm spacing between pins. These batteries require special charging. Do not attempt to charge these with anything but a specialized LiPo charger.

Battery includes built-in protection against over voltage, over current, and minimum voltage. Please use caution when using this battery in wearable projects. When using conductive thread, a short in the thread can create sparks and heat. We recommend using coin cell batteries for beginners.

Note: Although these cells are rated for 2C continuous discharge, the wiring and connectors are only rated up to 1A, so be sure to take that into account when determining your power requirements.

Note: Be careful with the JST connectors. They can stick in pretty good and tugging on them can damage the connector.

Dimensions: 5.7×29.5×48.27mm

Weight: 18.5g

Features:

• 2C continuous discharge
• Excellent long-term self-discharge rates (<8% per month)
• Robust power source under extreme conditions (-25 to 60C)

Don Luc

SparkFun: PRT-10718

Description: This is a very small, extremely light weight battery based on the new Polymer Lithium Ion chemistry. This is the highest energy density currently in production. Each cells outputs a nominal 3.7V at 400mAh! Comes terminated with a standard 2-pin JST-PH connector – 2mm spacing between pins. These batteries require special charging. Do not attempt to charge these with anything but a specialized Lithium Polymer charger.

Battery includes built-in protection against over voltage, over current, and minimum voltage. Please use caution when using this battery in wearable projects. When using conductive thread, a short in the thread can create sparks and heat. We recommend using coin cell batteries for beginners.

Note: Be careful with the JST connectors. They can stick in pretty good and tugging on them can damage the connector.

Dimensions: 5x25x35mm

Weight: 9g

Features:

• 2C continuous discharge – very high for low price
• Excellent long-term self-discharge rates (<8% per month)
• Robust power source under extreme conditions (-25 to 60C)

Don Luc

SparkFun: PRT-00731

Description: This is a very small, extremely light weight battery based on the new Polymer Lithium Ion chemistry. This is the highest energy density currently in production. Each cells outputs a nominal 3.7V at 110mAh! Comes terminated with a standard 2-pin JST-PH connector – 2mm spacing between pins. These batteries require special charging. Do not attempt to charge these with anything but a specialized Lithium Polymer charger.

Battery includes built-in protection against over voltage, over current, and minimum voltage. Please use caution when using this battery in wearable projects. When using conductive thread, a short in the thread can create sparks and heat. We recommend using coin cell batteries for beginners.

Note: Be careful with the JST connectors. They can stick in pretty good and tugging on them can damage the connector.

Dimensions: 5.7x12x28mm

Weight: 2.65g

Features:

• Excellent long-term self-discharge rates (<8% per month)
• Robust power source under extreme conditions (-25 to 60C)

Don Luc

SparkFun: PRT-10927

Description: These nylon standoffs are 3/8″ long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. The black nylon will give your project a very sessy look.

Sold in packs of 10.

Don Luc

SparkFun: PRT-10739

Description: Metal short standoffs: 3/8″ long x ¼”OD. Used to get your proto board up off the table. #4-40 thread. Fits all development boards with available holes. Don’t forget the screws!

Set of ten

Don Luc